请问谁知道9320接口的XT240364S的接口定义？ (amobbs.com 阿莫电子技术论坛) -

90999 发表于 2010-3-25 13:33:51

请问谁知道9320接口的XT240364S的接口定义？

在本地二手市场垃圾堆买到一个屏幕，型号XT240364S， 36pin的，在孤狗上查是XT240364SC............

请问谁知道9320接口的XT240364S的接口定义？

是不是9320的接口只要脚数一样都是通用的？

kunnsd 发表于 2010-3-25 22:48:10

没见过，能不能拍个照片上来呢？这样好判断些

90999 发表于 2010-3-26 21:36:13

已经联系了工厂，不知道工厂是否会给我资料，那位朋友是大公司的，帮我向这个工厂要这个屏些资料，我发了好多邮件过去没回音

屏架号 XT240364SF 排线号 XT240364SG

谢谢了

http://www.xl-display.com/

地址：广东省东莞市寮步镇西溪珠岗工业村
电话：0769-88909866 (三线)83030966
传真：0769-83283899
网址：www.xl-display.com
邮箱：xl-co@tom.com
Company@XL-Display.com
市场部：xl-co@xl-display.com
开发部：xl-rd@xl-display.com
采购部：xl-pur@xl-display.com

电话：0769-88909866
(三线)0769-83030966
传真：0769-83283899
网址：
www.xl-display.com
邮箱：
xl-co@tom.com
Company@XL-Display.com

90999 发表于 2010-3-29 10:56:43

祥龙是个手工作坊？

我朋友打了个电话过去，

0总机小姐爱理不理的，应付了一下找了一位大妈口音来接，大妈说还要问一下上面.....（又不给我转技术部）

靠，我本来看二手市场上他的屏幕瞒多的，想拿些回来（改排线）用来替代一些坏屏幕（同一驱动9320嘛）.....

现在倒好，工厂不理不睬，难怪二手市场上面那么多他们产的二手货，丢出来都没人要！！

窝火中......

90999 发表于 2010-3-31 19:43:02

终于得到规格表了，对方厂家需要签一份保密协议，折腾几天终于弄到了..........

还有一份代码，不知有啥用，传上来：

void ILI9320_Wintek24_Initial(void)
{
// VCI=2.8V
//************* Reset LCD Driver ****************//
LCD_nRESET = 1;
delayms(1); // Delay 1ms
LCD_nRESET = 0;
delayms(10); // Delay 10ms // This delay time is necessary
LCD_nRESET = 1;
delayms(50); // Delay 50 ms
//************* Start Initial Sequence **********//
LCD_CtrlWrite_ILI9320(0x00E5, 0x8000); // Set the internal vcore voltage
LCD_CtrlWrite_ILI9320(0x0000, 0x0001); // Start internal OSC.
LCD_CtrlWrite_ILI9320(0x0001, 0x0100); // set SS and SM bit
LCD_CtrlWrite_ILI9320(0x0002, 0x0700); // set 1 line inversion
LCD_CtrlWrite_ILI9320(0x0003, 0x1030); // set GRAM write direction and BGR=1.
LCD_CtrlWrite_ILI9320(0x0004, 0x0000); // Resize register
LCD_CtrlWrite_ILI9320(0x0008, 0x0202); // set the back porch and front porch
LCD_CtrlWrite_ILI9320(0x0009, 0x0000); // set non-display area refresh cycle ISC
LCD_CtrlWrite_ILI9320(0x000A, 0x0000); // FMARK function
LCD_CtrlWrite_ILI9320(0x000C, 0x0000); // RGB interface setting
LCD_CtrlWrite_ILI9320(0x000D, 0x0000); // Frame marker Position
LCD_CtrlWrite_ILI9320(0x000F, 0x0000); // RGB interface polarity
//*************Power On sequence ****************//
LCD_CtrlWrite_ILI9320(0x0010, 0x0000); // SAP, BT, AP, DSTB, SLP, STB
LCD_CtrlWrite_ILI9320(0x0011, 0x0000); // DC1, DC0, VC
LCD_CtrlWrite_ILI9320(0x0012, 0x0000); // VREG1OUT voltage
LCD_CtrlWrite_ILI9320(0x0013, 0x0000); // VDV for VCOM amplitude
delayms(200); // Dis-charge capacitor power voltage
LCD_CtrlWrite_ILI9320(0x0010, 0x17B0); // SAP, BT, AP, DSTB, SLP, STB
LCD_CtrlWrite_ILI9320(0x0011, 0x0137); // DC1, DC0, VC
delayms(50); // Delay 50ms
LCD_CtrlWrite_ILI9320(0x0012, 0x013C); // VREG1OUT voltage
delayms(50); // Delay 50ms
LCD_CtrlWrite_ILI9320(0x0013, 0x1900); // VDV for VCOM amplitude
LCD_CtrlWrite_ILI9320(0x0029, 0x001A); // VCM for VCOMH
delayms(50);
LCD_CtrlWrite_ILI9320(0x0020, 0x0000); // GRAM horizontal Address
LCD_CtrlWrite_ILI9320(0x0021, 0x0000); // GRAM Vertical Address
// ----------- Adjust the Gamma Curve ----------//
LCD_CtrlWrite_ILI9320(0x0030, 0x0002);
LCD_CtrlWrite_ILI9320(0x0031, 0x0606);
LCD_CtrlWrite_ILI9320(0x0032, 0x0501);
LCD_CtrlWrite_ILI9320(0x0035, 0x0206);
LCD_CtrlWrite_ILI9320(0x0036, 0x0504);
LCD_CtrlWrite_ILI9320(0x0037, 0x0707);
LCD_CtrlWrite_ILI9320(0x0038, 0x0306);
LCD_CtrlWrite_ILI9320(0x0039, 0x0007);
LCD_CtrlWrite_ILI9320(0x003C, 0x0700);
LCD_CtrlWrite_ILI9320(0x003D, 0x0700);
//------------------ Set GRAM area ---------------//
LCD_CtrlWrite_ILI9320(0x0050, 0x0000); // Horizontal GRAM Start Address
LCD_CtrlWrite_ILI9320(0x0051, 0x00EF); // Horizontal GRAM End Address
LCD_CtrlWrite_ILI9320(0x0052, 0x0000); // Vertical GRAM Start Address
LCD_CtrlWrite_ILI9320(0x0053, 0x013F); // Vertical GRAM Start Address
LCD_CtrlWrite_ILI9320(0x0060, 0x2700); // Gate Scan Line
LCD_CtrlWrite_ILI9320(0x0061, 0x0001); // NDL,VLE, REV
LCD_CtrlWrite_ILI9320(0x006A, 0x0000); // set scrolling line
//-------------- Partial Display Control ---------//
LCD_CtrlWrite_ILI9320(0x0080, 0x0000);
LCD_CtrlWrite_ILI9320(0x0081, 0x0000);
LCD_CtrlWrite_ILI9320(0x0082, 0x0000);
LCD_CtrlWrite_ILI9320(0x0083, 0x0000);
LCD_CtrlWrite_ILI9320(0x0084, 0x0000);
LCD_CtrlWrite_ILI9320(0x0085, 0x0000);
//-------------- Panel Control -------------------//
LCD_CtrlWrite_ILI9320(0x0090, 0x0010);
LCD_CtrlWrite_ILI9320(0x0092, 0x0000);
LCD_CtrlWrite_ILI9320(0x0093, 0x0003);
LCD_CtrlWrite_ILI9320(0x0095, 0x0110);
LCD_CtrlWrite_ILI9320(0x0097, 0x0000);
LCD_CtrlWrite_ILI9320(0x0098, 0x0000);
LCD_CtrlWrite_ILI9320(0x0007, 0x0173); // 262K color and display ON
}
void LCD_ExitSleep_ILI9320(void)
{
//*************Power On sequence ******************//
LCD_CtrlWrite_ILI9320(0x0010, 0x0000); // SAP, BT, AP, DSTB, SLP
LCD_CtrlWrite_ILI9320(0x0011, 0x0000); // DC1, DC0, VC
LCD_CtrlWrite_ILI9320(0x0012, 0x0000); // VREG1OUT voltage
LCD_CtrlWrite_ILI9320(0x0013, 0x0000); // VDV for VCOM amplitude
delayms(200); // Dis-charge capacitor power voltage
LCD_CtrlWrite_ILI9320(0x0010, 0x17B0); // SAP, BT, AP, DSTB, SLP, STB
LCD_CtrlWrite_ILI9320(0x0011, 0x0137); // DC1, DC0, VC
delayms(50); // Delay 50ms
LCD_CtrlWrite_ILI9320(0x0012, 0x013C); //VREG1OUT voltage
delayms(50); // Delay 50ms
LCD_CtrlWrite_ILI9320(0x0013, 0x1900); // VDV for VCOM amplitude
LCD_CtrlWrite_ILI9320(0x0029, 0x001A); //VCM for VCOMH
delayms(50);
LCD_CtrlWrite_ILI9320(0x0007, 0x0173); // 262K color and display ON
}
void LCD_EnterSleep_ILI9320(void)
{
LCD_CtrlWrite_ILI9320(0x0007, 0x0000); // display OFF
//************* Power OFF sequence **************//
LCD_CtrlWrite_ILI9320(0x0010, 0x0000); // SAP, BT, APE, AP, DSTB, SLP
LCD_CtrlWrite_ILI9320(0x0011, 0x0000); // DC1, DC0, VC
LCD_CtrlWrite_ILI9320(0x0012, 0x0000); // VREG1OUT voltage
LCD_CtrlWrite_ILI9320(0x0013, 0x0000); // VDV for VCOM amplitude
delayms(200); // Dis-charge capacitor power voltage
LCD_CtrlWrite_ILI9320(0x0010, 0x0002); // SAP, BT, APE, AP, DSTB, SLP
}

285123115 发表于 2010-7-1 14:20:46

楼主可否将PIN定义共享一下，我现在手头上也有这个模组，想要处理掉

90999 发表于 2010-7-1 14:38:01

可以给你，不过你调试好了要把代码公开出来，我写的不知道为什么工作不正常~~~~~~~

36PINourdev_565241HHV0AQ.pdf(文件大小:388K) (原文件名:GetAttachment.pdf)

285123115 发表于 2010-7-8 09:02:42

楼主，你给的附件不存在，下载不了，重新整一下吧。

其实调LCD并不复杂，硬件连接正确的话，一般只要把厂商给的Initial Code写进去就能工作，你发在四楼的那些就是它的Initial Code。

如果你没有让它工作起来，请先确定硬件没有问题，然后再找软件原因，做电子产品一定要先硬后软。

285123115 发表于 2010-7-8 15:22:52

楼主你的附件链接弄错了，应该是http://cache.ourdev.cn/bbs_upload672164/files_30/ourdev_565241HHV0AQ.pdf
这个链接可以下载。

这个屏的全部资料我都已经拿到了，准备用MPU接口的方式把它点亮，然后会把程序发给你。

90999 发表于 2010-7-22 05:41:07

回复【8楼】285123115
楼主你的附件链接弄错了，应该是http://cache.ourdev.cn/bbs_upload672164/files_30/ourdev_565241hhv0aq.pdf
这个链接可以下载。

这个屏的全部资料我都已经拿到了，准备用mpu接口的方式把它点亮，然后会把程序发给你。
-----------------------------------------------------------------------

奇怪，我也不知道为什么！

90999 发表于 2010-10-21 13:36:03

回复【10楼】zuoyi001左移一度
怎么没有下文了？！
-----------------------------------------------------------------------

拿了代码就跑的人太多了。小丑是不值一提的。

285123115 发表于 2010-11-5 16:18:10

回复【10楼】zuoyi001左移一度回复【11楼】90999 张耀扬
-----------------------------------------------------------------------
因为最近工作较忙，所以那个屏我一直没有时间去整，不过看到了【11楼】的回复，我加班加点把这个屏点亮了，现公布代码和测试图片。

回复【1楼】 90999 张耀扬
-----------------------------------------------------------------------
我用的屏和你的一模一样，是XT240364SG，硬件连接特性为：
CPU：STC89LE58RD+
LCD：采用i80/16-bit System Interface，用到LCD的：DB，DB，CS，RS，/WR共 19根数据线，第四脚IM3接地。
因为你四楼的初始化代码用的是RGB18接口，并且像素扫描设置的有点乱，所以我将它改为i80/16-bit System Interface，改了像素扫描设置。
还有这个LCD里面有四个灯，是串联的，需要12V电压才能点亮，我把它拆了改成了四灯并联，3.3V电压加一个33R的限流电阻就行了。

i80/16-bit System Interface初始化代码如下：
/**************************************************************************************************/
void LcdInitialization()
{
//LCD_CtrlWrite_ILI9320(0x00E5, 0x8000); // Set the internal vcore voltage
LCDCOM(0x00,0xE5); LCDDATA(0x80,0x00); Delay(1000); //Delay 1S
//LCD_CtrlWrite_ILI9320(0x0000, 0x0001); // Start internal OSC.
LCDCOM(0x00,0x00); LCDDATA(0x00,0x01); Delay(2000);
//LCD_CtrlWrite_ILI9320(0x0001, 0x0100); // set SS and SM bit R01H， //R60H，R03H：设置扫描方向，从上到下，从左到右
LCDCOM(0x00,0x01); LCDDATA(0x01,0x00);
//LCD_CtrlWrite_ILI9320(0x0002, 0x0700); // set 1 line inversion
LCDCOM(0x00,0x02); LCDDATA(0x07,0x00);
//LCD_CtrlWrite_ILI9320(0x0003, 0x1030); // set GRAM write direction and BGR=1. //R60H，R03H：设置扫描方向，从上到下，从左到右
LCDCOM(0x00,0x03); LCDDATA(0x10,0x30);
//LCD_CtrlWrite_ILI9320(0x0004, 0x0000); // Resize register
LCDCOM(0x00,0x04); LCDDATA(0x00,0x00);
//LCD_CtrlWrite_ILI9320(0x0008, 0x0202); // set the back porch and front porch
LCDCOM(0x00,0x08); LCDDATA(0x09,0x09);
//LCD_CtrlWrite_ILI9320(0x0009, 0x0000); // set non-display area refresh cycle ISC
LCDCOM(0x00,0x09); LCDDATA(0x00,0x00);
//LCD_CtrlWrite_ILI9320(0x000A, 0x0000); // FMARK function
LCDCOM(0x00,0x0A); LCDDATA(0x00,0x00);
//LCD_CtrlWrite_ILI9320(0x000C, 0x0000); // RGB interface setting //03设置为INTERNAL INTERFACE
LCDCOM(0x00,0x0C); LCDDATA(0x00,0x03);
//LCD_CtrlWrite_ILI9320(0x000D, 0x0000); // Frame marker Position
LCDCOM(0x00,0x0D); LCDDATA(0x00,0x00);
//LCD_CtrlWrite_ILI9320(0x000F, 0x0000); // RGB interface polarity
//LCDCOM(0x00,0x0F); LCDDATA(0x00,0x00);
//*************Power On sequence ****************//
//LCD_CtrlWrite_ILI9320(0x0010, 0x0000); // SAP, BT, AP, DSTB, SLP, STB
LCDCOM(0x00,0x10); LCDDATA(0x00,0x00);
//LCD_CtrlWrite_ILI9320(0x0011, 0x0000); // DC1, DC0, VC
LCDCOM(0x00,0x11); LCDDATA(0x00,0x00);
//LCD_CtrlWrite_ILI9320(0x0012, 0x0000); // VREG1OUT voltage
LCDCOM(0x00,0x12); LCDDATA(0x00,0x00);
//LCD_CtrlWrite_ILI9320(0x0013, 0x0000); // VDV for VCOM amplitude
LCDCOM(0x00,0x13); LCDDATA(0x00,0x00);
Delay(200); // Dis-charge capacitor power voltage
//LCD_CtrlWrite_ILI9320(0x0010, 0x17B0); // SAP, BT, AP, DSTB, SLP, STB
LCDCOM(0x00,0x10); LCDDATA(0x17,0xB0);
//LCD_CtrlWrite_ILI9320(0x0011, 0x0137); // DC1, DC0, VC
LCDCOM(0x00,0x11); LCDDATA(0x01,0x37);
Delay(50); // Delay 50ms
//LCD_CtrlWrite_ILI9320(0x0012, 0x013C); // VREG1OUT voltage
LCDCOM(0x00,0x12); LCDDATA(0x01,0x3C);
Delay(50); // Delay 50ms
//LCD_CtrlWrite_ILI9320(0x0013, 0x1900); // VDV for VCOM amplitude
LCDCOM(0x00,0x13); LCDDATA(0x17,0x00);
//LCD_CtrlWrite_ILI9320(0x0029, 0x001A); // VCM for VCOMH
LCDCOM(0x00,0x29); LCDDATA(0x00,0x1A);
Delay(50);
//LCD_CtrlWrite_ILI9320(0x0020, 0x0000); // GRAM horizontal Address
LCDCOM(0x00,0x20); LCDDATA(0x00,0x00);
//LCD_CtrlWrite_ILI9320(0x0021, 0x0000); // GRAM Vertical Address
LCDCOM(0x00,0x21); LCDDATA(0x00,0x00);
// ----------- Adjust the Gamma Curve ----------//
//LCD_CtrlWrite_ILI9320(0x0030, 0x0002);
LCDCOM(0x00,0x30); LCDDATA(0x00,0x02);
//LCD_CtrlWrite_ILI9320(0x0031, 0x0606);
LCDCOM(0x00,0x31); LCDDATA(0x06,0x06);
//LCD_CtrlWrite_ILI9320(0x0032, 0x0501);
LCDCOM(0x00,0x32); LCDDATA(0x05,0x01);
//LCD_CtrlWrite_ILI9320(0x0035, 0x0206);
LCDCOM(0x00,0x35); LCDDATA(0x02,0x06);
//LCD_CtrlWrite_ILI9320(0x0036, 0x0504);
LCDCOM(0x00,0x36); LCDDATA(0x05,0x04);
//LCD_CtrlWrite_ILI9320(0x0037, 0x0707);
LCDCOM(0x00,0x37); LCDDATA(0x07,0x07);
//LCD_CtrlWrite_ILI9320(0x0038, 0x0306);
LCDCOM(0x00,0x38); LCDDATA(0x03,0x06);
//LCD_CtrlWrite_ILI9320(0x0039, 0x0007);
LCDCOM(0x00,0x39); LCDDATA(0x00,0x07);
//LCD_CtrlWrite_ILI9320(0x003C, 0x0700);
LCDCOM(0x00,0x3C); LCDDATA(0x07,0x00);
//LCD_CtrlWrite_ILI9320(0x003D, 0x0700);
LCDCOM(0x00,0x3D); LCDDATA(0x07,0x00);
//------------------ Set GRAM area ---------------//
//LCD_CtrlWrite_ILI9320(0x0050, 0x0000); // Horizontal GRAM Start Address
LCDCOM(0x00,0x50); LCDDATA(0x00,0x00);
//LCD_CtrlWrite_ILI9320(0x0051, 0x00EF); // Horizontal GRAM End Address
LCDCOM(0x00,0x51); LCDDATA(0x00,0xEF);
//LCD_CtrlWrite_ILI9320(0x0052, 0x0000); // Vertical GRAM Start Address
LCDCOM(0x00,0x52); LCDDATA(0x00,0x01);
//LCD_CtrlWrite_ILI9320(0x0053, 0x013F); // Vertical GRAM Start Address
LCDCOM(0x00,0x53); LCDDATA(0x01,0x3f);
//LCD_CtrlWrite_ILI9320(0x0060, 0x2700); // Gate Scan Line //R60H，R03H：设置扫描方向，从上到下，从左到右
LCDCOM(0x00,0x60); LCDDATA(0xa7,0x00);
//LCD_CtrlWrite_ILI9320(0x0061, 0x0001); // NDL,VLE, REV
LCDCOM(0x00,0x61); LCDDATA(0x00,0x01);
//LCD_CtrlWrite_ILI9320(0x006A, 0x0000); // set scrolling line
LCDCOM(0x00,0x6A); LCDDATA(0x00,0x00);
//-------------- Partial Display Control ---------//
//LCD_CtrlWrite_ILI9320(0x0080, 0x0000);
LCDCOM(0x00,0x80); LCDDATA(0x00,0x00);
//LCD_CtrlWrite_ILI9320(0x0081, 0x0000);
LCDCOM(0x00,0x81); LCDDATA(0x00,0x00);
//LCD_CtrlWrite_ILI9320(0x0082, 0x0000);
LCDCOM(0x00,0x82); LCDDATA(0x00,0x00);
//LCD_CtrlWrite_ILI9320(0x0083, 0x0000);
LCDCOM(0x00,0x83); LCDDATA(0x00,0x00);
//LCD_CtrlWrite_ILI9320(0x0084, 0x0000);
LCDCOM(0x00,0x84); LCDDATA(0x00,0x00);
//LCD_CtrlWrite_ILI9320(0x0085, 0x0000);
LCDCOM(0x00,0x85); LCDDATA(0x00,0x00);
//-------------- Panel Control -------------------//
//LCD_CtrlWrite_ILI9320(0x0090, 0x0010);
LCDCOM(0x00,0x90); LCDDATA(0x00,0x10);
//LCD_CtrlWrite_ILI9320(0x0092, 0x0000);
LCDCOM(0x00,0x92); LCDDATA(0x00,0x00);
//LCD_CtrlWrite_ILI9320(0x0093, 0x0003);
LCDCOM(0x00,0x93); LCDDATA(0x00,0x03);
//LCD_CtrlWrite_ILI9320(0x0095, 0x0110);
LCDCOM(0x00,0x95); LCDDATA(0x01,0x10);
//LCD_CtrlWrite_ILI9320(0x0097, 0x0000);
LCDCOM(0x00,0x97); LCDDATA(0x00,0x00);
//LCD_CtrlWrite_ILI9320(0x0098, 0x0000);
LCDCOM(0x00,0x98); LCDDATA(0x00,0x00);
//LCD_CtrlWrite_ILI9320(0x0007, 0x0173); // 262K color and display ON
LCDCOM(0x00,0x07); LCDDATA(0x01,0x73);
}
/**************************************************************************************************/
自己写的坐标设置代码如下：
void SetWindows(unsigned char x1 ,unsigned char x2,unsigned int y1,unsigned int y2)
{
unsigned int i;
LCDCOM(0x00,0x20); LCDDATA(0x00,x1); //设置ADDRESS COUNTER原点
LCDCOM(0x00,0x21); LCDDATA((unsigned char)((i=y1)>>8),(unsigned char)(i=y1));

//LCD_CtrlWrite_ILI9320(0x0050, 0x0000); // Horizontal GRAM Start Address
LCDCOM(0x00,0x50); LCDDATA(0x00,x1);
//LCD_CtrlWrite_ILI9320(0x0051, 0x00EF); // Horizontal GRAM End Address
LCDCOM(0x00,0x51); LCDDATA(0x00,x2);
//LCD_CtrlWrite_ILI9320(0x0052, 0x0000); // Vertical GRAM Start Address
LCDCOM(0x00,0x52); LCDDATA((unsigned char)((i=y1)>>8),(unsigned char)(i=y1));
//LCD_CtrlWrite_ILI9320(0x0053, 0x013F); // Vertical GRAM Start Address
LCDCOM(0x00,0x53); LCDDATA((unsigned char)((i=y2)>>8),(unsigned char)(i=y2));
LCDCOM(0x00,0x22); //写入数据到GRAM
}
/**************************************************************************************************/

无图无真相，然后就是一些测试图片：
http://cache.amobbs.com/bbs_upload782111/files_34/ourdev_595522BVQDZO.jpg
测试图像，俄罗斯 (原文件名:IMAG0420.jpg)

http://cache.amobbs.com/bbs_upload782111/files_34/ourdev_595523P98MEH.jpg
测试图像，美女 (原文件名:IMAG0424.jpg)

http://cache.amobbs.com/bbs_upload782111/files_34/ourdev_595524VZV1RA.jpg
俄罗斯高清 (原文件名:IMAG0428.jpg)

http://cache.amobbs.com/bbs_upload782111/files_34/ourdev_595525JIJDMC.jpg
控制板和LCD板的背面 (原文件名:IMAG0431.jpg)

285123115 发表于 2010-11-5 16:55:24

回复【11楼】90999 张耀扬
-----------------------------------------------------------------------

才发现原来你就是楼主，最近太忙了，没多少时间去整这个东西，LCD和2G的NAND FLASH是我从一个旧MP4上拆下来的，算是废物利用了。

90999 发表于 2010-11-5 17:22:23

还可以拆开改灯啊？我丢着已经很久了。

cx6331989 发表于 2010-12-4 11:44:54

我也有一块这样的屏，不过不懂得用~~初学者~完全不懂，
资料好像下载不了楼主可以的话发给我
379714119@qq.com 有空的话发给我哈 thanks~~~

页: [1]

amobbs.com 阿莫电子技术论坛's Archiver

请问谁知道9320接口的XT240364S的接口定义？