gracialee 发表于 2017-4-28 11:33:53

GNI的机顶盒，型号MJD10-50,串口有消息，能搞成开发板玩玩？







Ok
TunerType = DCF8712
M13 Loader Version 1.2.0(nanhai)
building data:Aug 10 2003 time17:02:34
Starting Boot Loader
Run application...
Free Loader Mem
Execute application program!
Set SDRAM Poll!
STAVMEM_Init()=Ok,0xc0000000,0x4000,0x0
STAVMEM_CreatePartition()=Ok
STEVT_Init()=Ok
STPWM_Init()=Ok
STI2C_Init(back)=Ok
PTI_Init()=Ok
STCLKRV_Init(CLKRV0)=Ok
STCLKRV_Open(CLKRV0)=Ok
STAUD_Init(AUD0)=Ok
STDENC_Init(DENC0, InvOut 1)=Ok
STVTG_Init(VTG0)=Ok
STVID_Init(VID0)=Ok
STE2P_Init(EEPROM)=Ok
initterm.c, 1341   Info> Report module is initialized ...

ScrnParams.FrameRate =
Anti flicker filter enabled
   Fixbug.c, 0216   Info>   STOSD_Create dummy Region 4bpp

Creating Application Message queues...
LTV OS initialise...
LTV OS initialise OK.
LTV NVM initialise...
E2P_INIT_DATA:Blk- --- register.
E2P_INIT_DATA:Blk- --- register.
E2P_INIT_DATA:Blk- --- register.
E2P_INIT_DATA:Blk- ---   ok.
E2P_INIT_DATA:Blk- ---   ok.
E2P_INIT_DATA:Blk- ---   ok.
E2P_INIT_DATA:Blk- ---   ok.
block_used = 7,bytes_used = 1164
LTV NVM initialiseOK.
LTV GRAPH Initialise …
LTV GRAPH Initialise OK.
LTV INPUT Initialise...
LTV DEP Initialise OK in LTV_DEP_Initialise.
Initializing UART3!
Initialized UART3 Sucessed!!!
Initializing SmartCard!
Initialization SmartCard Sucessed!!!
Main Smart Card Init successed!
Open SmartCard Sucessed!
SC_SC_Initialise Main Smart Card Init Over !
enter OS init CTI !
enter NV_DRV_Initialise !
IRDETO SECTION FILTER Driver
Creating IRDETO SFILTER MONITOR Process
NO_OF_IRDETO_FILTERS equal to 20
Succesfully Installed IRDETO SFILTER module
SC_DRV_Initialise enter SC init CTI !
Smart Card Init Over !
SCELL_Ret_Value: 0
SECTION FILTER Driver version
Creating SFILTER MONITOR Process
NO_OF_SIMULTANEOUS_FILTERS equal to 8
Succesfully Installed SFILTER module
Initialise Timer Module Begin in LTV_TIMER_Initialise!
Initialise Timer Module Succeed in LTV_TIMER_Initialise!
Begin initialise system message module……
Initialise system message module success!
GNI SECTION FILTER Driver
Creating GNI SFILTER MONITOR Process
NO_OF_GNI_FILTERS equal to 20
Succesfully Installed GNI SFILTER module
GNI: SECT_REQ=> Slot
GNI: SECT_REQ=> Slot
Flash data:nvm_xpdr_db
Flash data:nvm_prg_db
Flash data:idto_mail
Block count
GNI: SECT_REQ=> Slot
uiByteUsed = 42652
LTV NVM access for(box_inf) ok.
GNI: SECT_REQ=> Slot
LTV NVM access for(app_cfg) ok.
LTV NVM access for(nvm_parent) ok.
GNI: SECT_REQ=> Slot
Get data.
transponder Initialisation: OK


Get data.
program Initialisation: OK


Get data.
DATABASE Driver version
TUNER (STV0297) Module Initialisation ver
Creating TUNER module semaphores ...
The Tuner type is DCF8712!
Switch to channel
Get Op_Code

Freq => Req Ret
TIDLE => left idle state
Set spectrum
pidCurVideo!
pidCurAudio!
pidCurPcr!
CA MPEG enable
STATUS Message
GNI: SECT_REQ=> Slot
CA MPEG-------------

pvSC_Notify(1, CARD_IN)
App Status: Smart Card verifying
STATUS Message
Get Op_Code
Get Op_Code
Get Op_Code
Get Op_Code
******* unlock(347000)******
Set spectrum
Get Op_Code
System id=
CHN
Nationality Code changed !
GetServiceDefine
CA MPEG-------------
STATUS Message
System id=
GetServiceDefine
CA MPEG-------------
Get Op_Code
******* unlock(347000)******
Set spectrum

qtechzdh 发表于 2017-4-28 22:59:50

没啥价值，软硬件都不开源。

elecfun 发表于 2017-4-28 23:34:53

公司这几天收拾，扔了几百台机顶盒，这些都是专用芯片，不开源个人没法玩的。

gzhuli 发表于 2017-4-28 23:49:38

如果是跑linux的还有机会折腾一下，这LTV OS什么鬼……

3DA502 发表于 2017-4-29 18:04:51

最多把DCF87 高频头给玩了

gracialee 发表于 2017-4-29 21:31:05

elecfun 发表于 2017-4-28 23:34
公司这几天收拾，扔了几百台机顶盒，这些都是专用芯片，不开源个人没法玩的。 ...

扔给我几台呗？我可以捎点银子，或者请你吃饭。{:lol:}

1a2b3c 发表于 2017-4-30 11:13:14

现在到处都在垃圾处理机顶盒，这个奇葩的怪物好像也要寿终正寝了，我一个搞这个的同学的确也宣告转行，5～10元一台成堆处理
页: [1]
查看完整版本: GNI的机顶盒，型号MJD10-50,串口有消息，能搞成开发板玩玩？