马超老师、傻孩子老师、shaoziyang老师,大家好!请教一下,bootloader在avr studio(gcc)
马超老师、傻孩子老师、shaoziyang老师,大家好!请教一下,bootloader在avr studio(gcc)的环境下应该怎么配置呀?我用是mega128这几天上网找了很多的资料也看了大家的讨论,ICC下的bootloader已经实现。但是avr studio(gcc)始终不行。
我主要代码如下,其中写flash代码是来自于http://www.nongnu.org/avr-libc/user-manual/group__avr__boot.html
unsigned char data1[]={…………………………………………};//这个是我希望用bootloader 写入的数组
void boot_program_page (uint32_t page, uint8_t *buf) //来源于avr-libc的范例
{
uint16_t i;
uint8_t sreg;
// Disable interrupts.
sreg = SREG;
cli();
eeprom_busy_wait ();
boot_page_erase (page);
boot_spm_busy_wait (); // Wait until the memory is erased.
for (i=0; i<SPM_PAGESIZE; i+=2)
{
// Set up little-endian word.
uint16_t w = *buf++;
w += (*buf++) << 8;
boot_page_fill (page + i, w);
}
boot_page_write (page); // Store buffer in flash page.
boot_spm_busy_wait(); // Wait until the memory is written.
// Reenable RWW-section again. We need this if we want to jump back
// to the application after bootloading.
boot_rww_enable ();
// Re-enable interrupts (if they were ever enabled).
SREG = sreg;
}
void main()//主函数,调用上面的函数,将数组写入对应的地址
{
……
address=0x0000;
boot_program_page(address,data1);
……
}
我的BOOTSZ1和BOOTSZ0都是取默认的0,即4096words, 32 pages;应用区0000~EFFF; boot:F000~FFFF直接在avr studio里面选好就行了。
同时BOOTRST也是默认,返回到0000;
另外,原来的帖子中写到需要在makefile 里面加上LDFLAGS = -Wl,-Map=$(TARGET).map,--cref,--section-start=工程名.text=0x1F000 但是这样不能写入。
或者,在memory 中设置memory:flash
name: 工程名.text
address: 0x1F000
也不成功。另外我尝试的地址有0x1e000也不行
lib中的代码应该是没问题的,我想请教大家,avr studio中具体的应该怎么设置啊? 不好意思啊,马潮老师的名字打错了~~~ 有会的朋友吗?可以QQ联系:374933900.我这急用 有大牛会吗?可付报酬,qq私聊:374933900 问题已经解决,上面的程序可以执行,问题出在project->configuration options->memory settings
点击 memory segments中add
第一个填“flash”
第二个填“.text”,这个表示是text
第三个填“0xfc00”,其实填其他的0xf800,0xf000都可以,但是注意要和熔丝位设置的一致才行
其实是老问题了,只是我是新手而已,呵呵,不好意思啊
页:
[1]